Milwaukee M28 C User Manual download pdf (Page 5)

8 9ENGLISH ENGLISH

TECHNICAL DATA

Voltage range .................................................................28 V

Quick charge current .....................................................3.5 A

Battery charging time ..........................................approx. 1 h

Weight according EPTA-Procedure 01/2003 ................700 g

WARNING! Read all safety warnings and all

instructions, including those given in the accompanying

brochure. Failure to follow the warnings and instructions

may result in electric shock, re and/or serious injury.

Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS

Do not dispose of used battery packs in the household

refuse or by burning them. Milwaukee Distributors offer to

retrieve old batteries to protect our environment.

Only the following battery packs can be charged with this

charger:

voltage battery rating No. of

(of storage battery) battery

cells

28 V M 28 BX 3.0 Ah 2 x 7

Do not try to charge non-rechargeable batteries with this

charger.

Do not store the battery pack together with metal objects

(short circuit risk).

No metal parts must be allowed to enter the battery section

of the charger (short circuit risk).

Never break open battery packs or chargers and store only

in dry rooms. Keep dry at all times.

The battery clamps of the charger are fed by the mains

supply. Do not touch the tool with conducting objects.

Never charge a damaged battery pack. Replace by a new

one.

Before use check machine, cable, and plug for any

damages or material fatigue. Repairs should only be carried

out by authorised Service Agents.

This appliance is not intended for use by persons (including

children) with limited physical, sensory or mental capabilities

or insufcient experience and/or knowledge unless they are

supervised by a person who is responsible for their safety or

have been instructed by them in the safe use of the tool.

Children should be supervised in order to ensure that they

do not play with the tool.

SPECIFIED CONDITIONS OF USE

The quick charger can charge Milwaukee M28 Li-Ion

batteries System M28 and V28 Li-Ion batteries System V28.

Do not use this product in any other way as stated for

normal use.

MAINS CONNECTION

Connect only to single-phase a.c. current and only to the

system voltage indicated on the rating plate. It is also

possible to connect to sockets without an earthing contact

as the design conforms to safety class II.

Li-Ion BATTERIES

The rechargeable batteries are partially charged and

supplied in a non-operative state. Prior to initial use it is

necessary to activate the battery by plugging it into the

charger briey. The LED on the battery indicates the state of

charge.

If it is not used for long periods, the rechargeable battery will

switch to the non-operative state and needs to be

reactivated before reuse.

The state of charge can be read by pressing the button on

the rechargeable battery. The battery can be left in the

electric tool while the reading is taken but it must be

switched off at least one minute beforehand (otherwise the

display will be inaccurate). The number of LEDs illuminated

indicates the state of charge.

As a general principle, if the electric tool should fail to work

after inserting the rechargeable battery, then the battery

should be plugged into the charger. The displays on the

battery and charger will then provide information about the

condition of the battery.

In low temperatures work may continue at reduced output.

For an optimum life-time, after use, the battery packs have

to be fully charged.

For battery pack storage longer than 30 days:

Store the battery pack where the temperature is below 27°C

and away from moisture

Store the battery packs in a 30% - 50% charged condition

Every six months of storage, charge the pack as normal.

To obtain the longest possible battery life remove the battery

pack from the charger once it is fully charged.

CHARACTERISTICS

After inserting the battery into the reception of the charger

the battery will automatically be charged (red control lamp is

illuminated continuously)

When a hot or cold battery pack is inserted into the charger

(ashing red lamp), charging will begin automatically once

the battery reaches the correct charging temperature

(0°C...65°C). The max. charging current is owing when the

temperature of the Li-Ion-battery is between 0°C and 65°C.

The battery’s charging time is between 1 min and 60 min (at

3,0 Ah), depending on the state of discharge.

Once the battery is fully charged, the LED on the charger

changes from red to green.

It is not necessary to remove the battery after charging. The

battery can be stored permanently in the charger without the

danger of being overcharged.

If both LEDs ash alternately then the rechargeable battery

is either not fully pushed in or there is a fault with the battery

or charger. Take the charger and battery out of use

immediately for safety reasons and have them inspected by

a Milwaukee customer service centre.

All LED will ash 4x if the machine is overloaded. To

continue working, switch the machine off and then on again.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that this product is

in conformity with the following standards or standardized

documents.

EN55014-1:2006 + A1:2009 + A2:2011

EN55014-2:1997 + A1:2001 + A2:2008

EN61000-3-2:2006 + A1:2009 + A2:2009

EN61000-3-3:2008

EN60335-1:2002 + A1:2004 + A11:2004 + A12:2006 +

A2:2006 + A13:2008 + A14:2010 + A15:2011

EN60335-2-29:2004 + A2:2010

EN62233:2008

in accordance with the regulations

2011/65/EU (RoHs)

2006/95/EC

2004/108/EC

Rainer Kumpf

Director Product Development

Winnenden, 2012-10-19

MAINTENANCE

If the supply cord of this appliance is damaged, it must only

be replaced by a repair shop appointed by the manufacturer,

because special purpose tools are required

Use only Milwaukee accessories and Milwaukee spare

parts. Should components need to be replaced which have

not been described, please contact one of our Milwaukee

service agents (see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered.

Please state the Article No. as well as the machine type

printed on the label and order the drawing at your local

service agents or directly at: Milwaukee Electric Tool,

Max-Eyth-Straße 10, D-71364 Winnenden, Germany.

SYMBOLS

Please read the instructions carefully before

starting.

Do not burn used battery packs.

Do not dispose of electric tools together with

household waste material! In observance of

European Directive 2002/96/EC on waste

electrical and electronic equipment and its

implementation in accordance with national law,

electric tools that have reached the end of their

life must be collected separately and returned to

an environmentally compatible recycling facility.

Never charge a damaged battery pack.

Replace with a new one.

This tool is only suitable for indoor use. Never

expose tool to rain.

1 2 3 4 5 6 7 8 9 10 ... 32 33

Comments to this Manuals

No comments

Milwaukee M28 C User Manual Page 5

Comments to this Manuals

Related products and manuals for Power tools Milwaukee M28 C