Milwaukee 4115 Operator's Manual download pdf (Page 6)

6 www.amplificleaning.com

Assembly

Read entire operator’s manual before you attempt to

assemble or operate your new Hose Powering

System.

Your Hose Powering System requires some assembly but

is quickly ready for use. If you have any problems with the

assembly of your Hose Powering System, please call the Hose

Powering System helpline at (800) 743-4115.

Tools Needed

 • Needlenosepliers.

 • Phillipsscrewdriver.

Items Not Included

 • Long(100ft[30.48m]max.)Amplifibrandheavyduty

garden hose or equivalent with 400 psi minimum burst

pressure.

 • 4AABatteries.

Unpack Hose Powering System

1. Remove everything from carton except for the pump and

hose pot assembly.

2. Open carton completely by cutting each corner from top to

bottom to remove the pump and hose pot assembly.

Items in the carton include:

 • Pumpandhosepotassembly

 • Hosepotcover

 • Spraygunwithdetergentbottle

 • Detachabletransporthandle

 • 15ft(4.5m)inletgardenhose

 • Partsbag(whichincludesthefollowing):

  • Operator’smanual

  • Owner’sregistrationcard

Check all contents. If any parts are missing or damaged, call the

Hose Powering System helpline at (800) 743-4115.

Become familiar with each component before assembling the

Hose Powering System. Identify contents with the illustration

shown in Features and Controls.

Prior to Operation

1. Please fill out and send in the registration card.

2. Read and perform the following instructions while paying

close attention to all warnings and notices.

NOTICE Connect ONLY to water source capable of supplying

a minimum of 6 gpm at 30 psi. Inspect all equipment, hoses

and accessories thoroughly before each use, DO NOT use if

damaged.

• DO NOT use light duty discharge garden hose.

• ONLY use branded accessories intended for use with this

product.

• For optimum performance, use a 15 foot inlet hose and 50 foot

discharge hose 5/8 inch or greater.

• Replace only with original equipment parts.

• To order, call (800) 743-4115 or visit

www.amplificleaning.com.

Install Batteries Into Spray Gun

1. Remove screw (A) from battery pack (B).

2. Remove battery pack.

3. Open battery door (C). Be careful not to damage rubber seal.

4. Insert 4 AA batteries (D) into battery pack EXACTLY as

illustrated.

5. Close battery door.

6. Replace battery pack onto spray gun.

7. Replace screw in battery pack.

Connect Hoses and Water Supply

NOTICE Use ONLY cold water (less than 100°F).

1. Attach 15 ft. (short) inlet garden hose to water supply.

2. Run water through inlet garden hose for 30 seconds to flush

the hose of debris. Turn off water.

3. Remove and discard shipping cap from the unit’s water inlet

using a needle nose pliers.

4. Confirm water inlet screen (E) is installed.

NOTICE If inlet screen is damaged or missing, DO NOT use

Hose Powering System. Call (800) 743-4115 for assistance.

NOTICE DO NOT run the pump without the water supply

connected and turned on.

 • Damagetoequipmentresultingfromfailuretofollowthis

instruction will void warranty.

5. Attach opposite end of 15 ft. inlet garden hose to Hose

Powering System’s water inlet coupling (E). Tighten by hand.

1 2 3 4 5 6 7 8 9 10 11 ... 15 16

Comments to this Manuals

No comments

Milwaukee 4115 Operator's Manual Page 6

Comments to this Manuals