Milwaukee 5317-20 User Manual download pdf (Page 3)

FASTENER TORQUE SPECIFICATIONS (FT./LBS.)

SEATING TORQUE

FIG. NO. WHERE USED In/Lbs Nm

21a Belly Shroud - 1x 19-25 2.2-2.8

21b Selector Bracket Clamp Plate - 2x 19-25 2.2-2.8

29a Gearcase Cover (middle & front positions - 4x) 50-55 5.6-6.2

29b Gearcase Cover (rear position - 2x) 35-40 4.0-4.6

46a Motor End Cover - 2x 8-12 0.9-1.4

46b Cord Clamp - 2x 10-16 1.2-1.8

48 Motor Housing - 4x 47-53 5.4-6.0

52 Brush Holder Assemblies - 2x 10-16 1.2-1.8

56 Field - 2x 16-21 1.8-2.4

64 Handle Cover - 4x 23-28 2.6-3.2

Switch Screw - 2x 3.5-6 0.4-0.7



22-18-6030 BRUSH SERVICE KIT

THIS KIT CONTAINS:

1 --------------- Carbon Brush

1 --------------- Carbon Brush with Pop Off

14-46-6010 MAINTENANCE SERVICE KIT

THIS KIT CONTAINS:

1 45-12-5316 Rubber Dust Shield

1 34-60-5316 Retaining Ring

2 34-40-5316 Spindle O-Ring

2 34-60-5319 O-Ring

2 34-60-5321 O-Ring

1 45-06-5170 Felt Seal

1 45-06-5180 Rotary Seal

1 45-88-5323 O-Ring

2 45-06-5317 Turcon Seal

1 34-40-5321 Back Press Ring

2 34-40-5310 O-Ring

1 45-06-5316 Rubber Gasket

2 34-40-5308 O-Ring

1 22-18-6030 Brush Service Kit (Set of 2)

1 49-08-5355 ‘Q2’ Grease (2.8oz/80g tube)

Pack the rear of the piston

with grease. There is to be

no lubrication on the face

of the part.

Place 2-3/16 oz. (62g)

of grease in the bottom

of the gearcase

Place 5/8 oz. (18g) of grease

in the rear of the barrel before

installing the striker

Coat the inside

of the spindle driver

prior to assembly

Coat teeth of

clutch assembly

with grease

Coat o-ring and

o-ring groove prior

to installing o-ring.

With o-ring

installed, coat around

entire side of ram

17h 19

Washer

#19 is to be

located here on

barrel #17h

Fig. 1

Small

hole in

barrel

1. Place washer #19 onto backside of barrel.

2. Place 18 grams of ‘Q2’ grease inside barrel.

3. Coat o-ring groove on ram

and o-ring with grease prior

to installing o-ring on ram.

Coat the assembled ram and

o-ring with grease as shown

below.

4. When placing ram assembly

into barrel, slowly apply

pressure to ram assembly.

5. Push the ram assembly until

rear face is just below small

hole in the barrel. DO NOT

wipe off any excess grease

that oozes out of holes.

No grease on rear

face of ram (striker)

#18a

Washer

#19

LUBRICATION NOTES:

Type ‘Q2’ Grease, No. 49-08-5355

(2.8oz, 80g tube)

Prior to reinstalling, clean gear assemblies with

a clean, dry cloth. Lightly coat all individual

parts highlighted here with grease. Apply a

greater amount of grease to all internal and

external gear teeth. Place 18 grams

of grease in the rear of the barrel

prior to inserting the ram. Place the

remaining grease in the

bottom of the gearcase.

Lubrication Note: MILWAUKEE recommends that scheduled maintenance of this Rotary

Hammer include lubrication replacement, and replacement of vital O-rings and gaskets at each

carbon brush change. Doing so will prolong the life of the hammer by reducing wear to gears

and mechanism parts. The carbon brushes and armature commutator in this MILWAUKEE

Rotary Hammer are designed and matched for many hours of reliable performance.

1 2 3 4

Comments to this Manuals

No comments

Milwaukee 5317-20 User Manual Page 3

Comments to this Manuals

Related products and manuals for Rotary hammers Milwaukee 5317-20