Milwaukee 6370-20 User Manual download pdf (Page 7)

page 7

WARNING

TOOL ASSEMBLY

To reduce the risk of injury, always unplug tool before attaching

or removing accessories or making adjustments. Use only speciﬁ -

cally recommended accessories. Others may be hazardous.

Selecting Blade

Select a blade appropriate for your application. Refer to the “Accessories”

section for a list of blades for this tool.

Always use sharp blades. Dull blades tend to overload the tool and increase

the chance of KICKBACK. Only use blades with a maximum safe operating

speed greater than the no load RPM marked on the tool's nameplate. Read

the blade manufacturer's instructions before use. Do not use any type of

abrasive cut-off wheel or dry diamond cutting blades. Use the correct blade

type for your application. Using the wrong blade may result in reduced

performance or damage to the blade. Do not use blades that are cracked

or have broken teeth.

Checking the Operation of the Lower Guard

Check the operation and condition of the lower guard lever. If the guard and

the lever are not operating properly, they must be serviced before use. Lower

guard may operate sluggishly due to damaged parts, gummy deposits, or

a buildup of debris.

1. Unplug tool before checking the lower guard.

2. Place the tool on its side (Fig. 1).

NOTE: This procedure will not show proper lower guard operation if

the tool is not on its side.

3. Grasp the lower guard by the sides and push it all the way back into

the blade housing.

4. Release the lower guard.

• If the guard immediately springs back into place, it is working correctly

and you may continue with use.

• If the guard does not immediate spring back into place, clean the upper

and lower guards to remove all chips and debris. Then, check

the operation again by starting with step 1.

• If the guard still does not immediately spring back into place, contact a

MILWAUKEE service facility for repairs.

Removing and Installing Chip Container

6. Place the blade ﬂ ange on the spindle and hand tighten the blade

bolt.

7. While holding in the spindle lock button, use the wrench to turn the

blade bolt clockwise and tighten securely.

8. Replace the chip container (see "Removing and Installing Chip Con-

WARNING

• NEVER operate tool when guards and chip container are not

installed. Serious injury may occur.

• To reduce the risk of injury, wear safety goggles or glasses

with side shields when removing the chip container. Chips and

debris may ﬂ y up into the face.

Fig. 1

To remove, turn

counterclockwise

Spindle lock

button

1. Unplug tool before removing or installing chip container.

2. To remove the chip container, open the latch and pull the chip container

off of the tab.

3. To install the chip container, ﬁ t the tab pin onto the tab, position the

chip container, and secure the latch.

1. Unplug tool before installing or removing blades.

2. Remove the chip container (see "Removing and Installing Chip Con-

tainer").

3. Place the saw on a ﬂ at surface with the blade facing up (Fig. 1). To

remove the blade bolt from the spindle, push in the spindle lock button

and hold. Using the wrench provided with the tool, turn the blade bolt

counterclockwise. Remove the blade bolt and outer blade ﬂ ange. Do

not remove the inner blade ﬂ ange.

4. Remove the blade from the spindle. Always clean the spindle, upper

guard, lower guard, and blade ﬂ anges to remove any chips and de-

bris.

5. To install a blade, place the blade on the spindle with the teeth

pointing in the same direction as the arrow on the lower guard

(Fig. 2).

Installing and Removing Blades (Figs. 1 & 2)

Fig. 2

1 2 3 4 5 6 7 8 9 10 11 12 ... 31 32

Comments to this Manuals

No comments

Milwaukee 6370-20 User Manual Page 7

Comments to this Manuals

Related products and manuals for Power saws Milwaukee 6370-20